语言
Magnetron sputtering (磁控溅射台))

新闻资讯

热门关键词

联系我们

名 称:苏州赛森电子科技有限公司

电 话:0512-58987901

传 真:0512-58987201

邮 箱:sales@cycas.com

地 址:江苏省张家港经济开发区福新路1202号 215600PRC

网 址:www.cycas.com

Name: Suzhou cycas  Microelectronics Co., Ltd.

Tel.: 0512-58987901

Fax: 0512-58987201

Email: sales@cycas.com

Address: No.1202,Fuxin Road,Zhangjiagang Economic Development Zone,Jiangsu Province 215600PRC

Website: www.cycas.com 

等离子刻蚀机的检验操作及处理模式    Inspection operation and treatment mode of plasma etcher

您的当前位置: 首 页 >> 新闻资讯 >> 行业新闻

等离子刻蚀机的检验操作及处理模式    Inspection operation and treatment mode of plasma etcher

发布日期:2019-11-28 作者: 点击:

等离子刻蚀机的检验操作及处理模式

TIM图片20191128104055.png

  等离子刻蚀机的原理是在真空状态下,利用射频辐射使得氧、氩、氮、四氟化碳等气体生成具有高反应活性的离子与器件等反应形成挥发性化合物,然后由真空系统奖这些挥发性物质清除出去。

  

    一、等离子刻蚀机检验操作及判断

  1.确认万用表工作正常,量程置于200mV。

  2.冷探针连接电压表的正电极,热探针与电压表的负极相连。

  3.用冷、热探针接触硅片一个边沿不相连的两个点,电压表显示这两点间的电压为正值,说明导电类型为P型,刻蚀合格。相同的方法检测另外三个边沿的导电类型是否为P型。

  4.如果经过检验,任何一个边沿没有刻蚀合格,则这一批硅片需要重新装片,进行刻蚀。

  

    二、等离子刻蚀机处理模式:

  直接模式——基片可以直接放置在电极托架或是底座托架上,以获得zui大的平面刻蚀效果。

  定向模式——需要非等向性刻蚀(anisotropicetching)的基片可以放置在特制的平面托架上。

  下游模式——基片可以放置在不带电托架上,以便取得微小的等离子体效果。

  定制模式——当平面刻蚀配置不过理想时,特制的电极配置可以提供。


 

                                           Inspection operation and treatment mode of plasma etcher

  The principle of plasma etcher is that in vacuum, oxygen, argon, nitrogen, carbon tetrafluoride and other gases are generated into highly reactive ions by radio-frequency radiation, which react with devices to form volatile compounds, which are then removed by vacuum system award.

1Inspection operation and judgment of plasma etcher

1. Confirm that the multimeter works normally and the range is set at 200mV.

2. The cold probe is connected to the positive electrode of the voltmeter, and the hot probe is connected to the negative electrode of the voltmeter.

3. Use cold and hot probes to contact two points on one edge of the silicon wafer that are not connected. The voltmeter shows that the voltage between the two points is positive, indicating that the conductive type is p-type, and the etching is qualified. The same method is used to detect whether the conductive type of the other three edges is p-type.

4. If any edge is not etched as qualified after inspection, this batch of silicon wafers need to be reloaded for etching.

2 Plasma etcher processing mode:

Direct mode - the substrate can be placed directly on the electrode bracket or the base bracket to achieve a large Zui planar etching effect.

Orientation mode - substrate requiring anisotropic etching can be placed on a special plane bracket.

Downstream mode - the substrate can be placed on an uncharged bracket to achieve a small plasma effect.

Custom mode - when the planar etching configuration is not ideal, a special electrode configuration can be provided.


本文网址:http://www.cycas.com/news/437.html

相关标签:等离子刻蚀机

最近浏览: