语言
Magnetron sputtering (磁控溅射台))

新闻资讯

热门关键词

联系我们

名 称:苏州赛森电子科技有限公司

电 话:0512-58987901

传 真:0512-58987201

邮 箱:sales@cycas.com

地 址:江苏省张家港经济开发区复兴路2号B06栋1楼215600PRC

网 址:www.cycas.com

Name: Suzhou cycas  Microelectronics Co., Ltd.

Tel.: 0512-58987901

Fax: 0512-58987201

Email: sales@cycas.com

Address: 1st floor,B06 building,No.2,Fuxing Road,Zhangjiagang Economic Development Zone,Jiangsu Province 215600PRC

Website: www.cycas.com 

Microwave plasma dry degumming machine operation and personnel微波等离子干法去胶机操作及配合人员防护:

您的当前位置: 首 页 >> 新闻资讯 >> 技术知识

Microwave plasma dry degumming machine operation and personnel微波等离子干法去胶机操作及配合人员防护:

发布日期:2019-03-02 作者:www.cycas.com 点击:

  微波等离子干法去胶机操作及配合人员防护:

  1、作业后,应切断电源,关闭气源和水源;

  2、高空切割时,必须系好安全带,切接切割周围和下方应采取防火措施,并应有专人监护;

  3、现场使用的等离子切割机机,应设有防雨、防潮、防晒的机棚,并应装设相应的消防器材;

  4、雨天不得在露天焊割。在潮湿地带作业时,操作人员应站在铺有绝缘物品的地方,并应穿绝缘鞋;

  5、对承压状态的压力容器及管道、带电设备、承载结构的受力部位和装有易燃、易爆物品的容器严禁进行切割;

  6、当需微波等离子去胶机受压容器、密封容器、油桶、管道、沾有可燃气体和溶液的工件时,应先消除容器及管道内压力,消除可燃气体和溶液,然后冲洗有毒、有害、易燃物质;对存有残余油脂的容器,应先用蒸汽、碱水冲洗,并打开盖口,确认容器清洗干净后,再灌满清水方可进行切割。在容器内焊割应采取防止触电、中毒和窒息的措施。割密封容器应留出气孔,必要时在进、出气口处装设备通风设备;容器内照明电压不得超过12V,焊工与工件间应绝缘;容器外应设专人监护。微波等离子去胶机操作者严禁在已喷涂过油漆和塑料的容器内切割。

    Microwave plasma dry degumming machine operation and personnel

    1. After operation, cut off the power supply, turn off the air source and water source; 

    2. When cutting at high altitude, fasten the safety belt, take fire prevention measures around and below the cutting, and assign special personnel for supervision;

    3. The plasma cutting machine used on site shall be equipped with rain proof, moisture-proof and sun proof machine shed, and shall be equipped with corresponding fire-fighting equipment; 

    4. It is not allowed to weld and cut in the open air in rainy days.When working in a humid area, the operator shall stand at the place with insulating materials and wear insulating shoes;

   5. It is strictly prohibited to cut the pressure vessels and pipelines under pressure, the stressed parts of electrified equipment and bearing structure, and the vessels with inflammable and explosive materials;

   6. When the pressure vessel, sealed vessel, oil barrel, pipeline and workpieces stained with combustible gas and solution of microwave plasma degummer are required, the pressure in the vessel and pipeline shall be eliminated first to eliminate the combustible gas and solution, and then the toxic, harmful and flammable substances shall be flushed; for the vessel with residual grease, the steam and alkaline water shall be used to flush first, and the cover opening shall be opened to confirm that the vessel is cleaned , and then fill with water before cutting. Measures shall be taken to prevent electric shock, poisoning and suffocation during welding and cutting in the container. Air holes shall be reserved for cutting sealed containers, and ventilation equipment shall be installed at the air inlet and outlet if necessary; the lighting voltage in the container shall not exceed 12V, and the welder and workpiece shall be insulated; a special person shall be arranged outside the container for supervision. The operator of microwave plasma degumming machine is forbidden to cut in the container which has been sprayed with paint and plastic


干法去胶机

本文网址:http://www.cycas.com/news/378.html

相关标签:干法去胶机

最近浏览: